code cleanup and format

src/hoverserial.ino

@@ -15,10 +15,10 @@
 // by JbLb
 // • Converted to platformio
 // • Adapted to Arduino leonardo to use CDC serial interface
-// • Serial1 connected to hoverboard board 
+// • Serial1 connected to hoverboard board
 // • CDC used to display data on serial monitor
 
-// 
+//
 // CONFIGURATION on the hoverboard side in config.h:
 // • Option 1: Serial on Left Sensor cable (long wired cable)
 //   #define CONTROL_SERIAL_USART2
@@ -34,7 +34,7 @@
 #define HOVER_SERIAL_BAUD   38400       // [-] Baud rate for HoverSerial (used to communicate with the hoverboard)
 #define SERIAL_BAUD         115200      // [-] Baud rate for built-in Serial (used for the Serial Monitor)
 #define START_FRAME         0xAAAA     	// [-] Start frme definition for reliable serial communication
-#define TIME_SEND           100         // [ms] Sending time interval
+#define TIME_SEND           1000        // [ms] Sending time interval
 #define SPEED_MAX_TEST      300         // [-] Maximum speed for testing
 //#define DEBUG_RX                        // [-] Debug received data. Prints all bytes to serial (comment-out to disable)
 
@@ -80,11 +80,10 @@ SerialFeedback NewFeedback;
 #define SCREEN_HEIGHT 64 // OLED display height, in pixels
 
 // Declaration for an SSD1306 display connected to I2C (SDA, SCL pins)
-#define OLED_RESET     -1 // Reset pin # (or -1 if sharing Arduino reset pin)
-Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire, OLED_RESET);
+Adafruit_SSD1306 display(SCREEN_WIDTH, SCREEN_HEIGHT, &Wire);
 
 // ########################## SETUP ##########################
-void setup() 
+void setup()
 {
 
 	display.begin(SSD1306_SWITCHCAPVCC, 0x3C); // initialize with the I2C addr 0x3C (for the 128x64)
@@ -98,11 +97,11 @@ void setup()
 	display.println("v1.0");
 	display.display();
 
-	Serial1.begin(HOVER_SERIAL_BAUD);  // RX, TX from arduino to TX RX on hoverboard board. ! be carreful 3v3 
-  	pinMode(LED_BUILTIN, OUTPUT);
+	Serial1.begin(HOVER_SERIAL_BAUD);  // RX, TX from arduino to TX RX on hoverboard board. ! be carreful 3v3
+	pinMode(LED_BUILTIN, OUTPUT);
 
 	  Serial.begin(SERIAL_BAUD);
-  	if (Serial) {
+	if (Serial) {
 		Serial.println("Hoverboard Serial v1.0");
 	}
 }
@@ -110,14 +109,14 @@ void setup()
 // ########################## SEND ##########################
 void Send(int16_t uSteer, int16_t uSpeed)
 {
-  // Create command
-  Command.start    = (uint16_t)START_FRAME;
-  Command.steer    = (int16_t)uSteer;
-  Command.speed    = (int16_t)uSpeed;
-  Command.checksum = (uint16_t)(Command.start ^ Command.steer ^ Command.speed);
-
-  // Write to Serial
-  Serial1.write((uint8_t *) &Command, sizeof(Command)); 
+	// Create command
+	Command.start    = (uint16_t)START_FRAME;
+	Command.steer    = (int16_t)uSteer;
+	Command.speed    = (int16_t)uSpeed;
+	Command.checksum = (uint16_t)(Command.start ^ Command.steer ^ Command.speed);
+
+	// Write to Serial
+	Serial1.write((uint8_t *) &Command, sizeof(Command));
 }
 
 // ########################## RECEIVE ##########################
@@ -126,7 +125,7 @@ void Receive()
 	// Check for new data availability in the Serial buffer
 	if (Serial1.available()) {
 		incomingByte 	  = Serial1.read();		                              // Read the incoming byte
-		bufStartFrame	= ((uint16_t)(incomingBytePrev) << 8) +  incomingByte;	// Construct the start frame		
+		bufStartFrame	= ((uint16_t)(incomingBytePrev) << 8) +  incomingByte;	// Construct the start frame
 	}
 	else {
 		return;
@@ -136,30 +135,30 @@ void Receive()
   #ifdef DEBUG_RX
 		Serial.print(incomingByte);
 		return;
-  #endif    	
-	
+  #endif
+
 	// Copy received data
 	if (bufStartFrame == START_FRAME) {	                    // Initialize if new data is detected
 		p 		= (byte *)&NewFeedback;
 		*p++ 	= incomingBytePrev;
-		*p++ 	= incomingByte;		
-		idx 	= 2;		
+		*p++ 	= incomingByte;
+		idx 	= 2;
 	} else if (idx >= 2 && idx < sizeof(SerialFeedback)) {	// Save the new received data
-		*p++ 	= incomingByte; 
+		*p++ 	= incomingByte;
 		idx++;
-	}	
-	
+	}
+
 	// Check if we reached the end of the package
-	if (idx == sizeof(SerialFeedback)) {  	
+	if (idx == sizeof(SerialFeedback)) {
 		uint16_t checksum;
 		checksum = (uint16_t)(NewFeedback.start ^ NewFeedback.cmd1 ^ NewFeedback.cmd2 ^ NewFeedback.speedR ^ NewFeedback.speedL
 					^ NewFeedback.speedR_meas ^ NewFeedback.speedL_meas ^ NewFeedback.batVoltage ^ NewFeedback.boardTemp);
-	
+
 		// Check validity of the new data
 		if (NewFeedback.start == START_FRAME && checksum == NewFeedback.checksum) {
 			// Copy the new data
 			memcpy(&Feedback, &NewFeedback, sizeof(SerialFeedback));
-		  
+
 			// Print data to CDC Serial if available
 			if (Serial) {
 				Serial.print("1: ");   Serial.print(Feedback.cmd1);
@@ -174,10 +173,10 @@ void Receive()
 		} else {
 		  if (Serial) Serial.println("Non-valid data skipped");
 		}
-		
+
 		idx = 0;	// Reset the index (it prevents to enter in this if condition in the next cycle)
 	}
- 	
+
 	// Update previous states
 	incomingBytePrev 	= incomingByte;
 }