change for motor control board new firmware

src/hoverserial.ino

@@ -30,7 +30,7 @@
 //   // #define DEBUG_SERIAL_USART3
 // *******************************************************************
 
-#define VERSION_TAG         "V test 0.1"
+#define VERSION_TAG         "V test 0.2"
 #define BTN_PLUS            4
 #define BTN_MOINS           5
 #define BTN_MARCHE          6
@@ -38,16 +38,16 @@
 
 
 // ########################## DEFINES ##########################
-#define HOVER_SERIAL_BAUD   38400       // [-] Baud rate for HoverSerial (used to communicate with the hoverboard)
+#define HOVER_SERIAL_BAUD   115200       // [-] Baud rate for HoverSerial (used to communicate with the hoverboard)
 #define SERIAL_BAUD         115200      // [-] Baud rate for built-in Serial (used for the Serial Monitor)
-#define START_FRAME         0xAAAA      // [-] Start frme definition for reliable serial communication
+#define START_FRAME         0xABCD      // [-] Start frme definition for reliable serial communication
 #define TIME_SEND           25        // [ms] Sending time interval
 #define SPEED_MAX_TEST      300 // [-] Maximum speed for testing
 //#define DEBUG_RX                        // [-] Debug received data. Prints all bytes to serial (comment-out to disable)
 
 // ########################## macros ############################
 
-#include <EEPROM.h> 
+#include <EEPROM.h>
 
 #include <FastLED.h>
 
@@ -76,13 +76,12 @@ typedef struct {
     uint16_t start;
     int16_t cmd1;
     int16_t cmd2;
-    int16_t speedR;
-    int16_t speedL;
     int16_t speedR_meas;
     int16_t speedL_meas;
     int16_t batVoltage;
     int16_t boardTemp;
-    int16_t checksum;
+    uint16_t cmdLed;
+    uint16_t checksum;
 } SerialFeedback;
 SerialFeedback Feedback;
 SerialFeedback NewFeedback;
@@ -116,7 +115,7 @@ CRGB leds[NUM_LEDS];
 
 // ########################## SETUP ##########################
 void setup()
-{    
+{
     pinMode(BTN_MARCHE, INPUT_PULLUP);
     pinMode(BTN_PLUS, INPUT_PULLUP);
     pinMode(BTN_MOINS, INPUT_PULLUP);
@@ -188,11 +187,8 @@ void Receive()
     if (idx == sizeof(SerialFeedback)) {
         uint16_t checksum;
         checksum =
-            (uint16_t) (NewFeedback.start ^ NewFeedback.cmd1 ^ NewFeedback.
-                        cmd2 ^ NewFeedback.speedR ^ NewFeedback.
-                        speedL ^ NewFeedback.speedR_meas ^ NewFeedback.
-                        speedL_meas ^ NewFeedback.batVoltage ^ NewFeedback.
-                        boardTemp);
+            (uint16_t) (NewFeedback.start ^ NewFeedback.cmd1 ^ NewFeedback.cmd2 ^ NewFeedback.speedR_meas ^ NewFeedback.speedL_meas
+                            ^ NewFeedback.batVoltage ^ NewFeedback.boardTemp ^ NewFeedback.cmdLed);
 
         // Check validity of the new data
         if (NewFeedback.start == START_FRAME
@@ -207,17 +203,17 @@ void Receive()
                 Serial.print(" 2: ");
                 Serial.print(Feedback.cmd2);
                 Serial.print(" 3: ");
-                Serial.print(Feedback.speedR);
+                Serial.print(Feedback.speedR_meas);
                 Serial.print(" 4: ");
-                Serial.print(Feedback.speedL);
+                Serial.print(Feedback.speedL_meas);
                 Serial.print(" 5: ");
-                Serial.print(Feedback.speedR_meas);
+                Serial.print(Feedback.batVoltage);
                 Serial.print(" 6: ");
-                Serial.print(Feedback.speedL_meas);
+                Serial.print(Feedback.boardTemp);
                 Serial.print(" 7: ");
-                Serial.print(Feedback.batVoltage);
-                Serial.print(" 8: ");
-                Serial.println(Feedback.boardTemp);
+                Serial.println(Feedback.cmdLed);
+
+
             }
         } else {
             if (Serial)
@@ -243,7 +239,7 @@ void EEPROMWriteInt(int p_address, int p_value)
      }
 
 //This function will read a 2 byte integer from the eeprom at the specified address and address + 1
-unsigned int EEPROMReadInt(int p_address)
+int EEPROMReadInt(int p_address)
      {
      byte lowByte = EEPROM.read(p_address);
      byte highByte = EEPROM.read(p_address + 1);
@@ -284,7 +280,7 @@ void run_control(void) {
         last_marche = false;
     }
 }
- 
+
 void speed_control(void) {
     if (run_mode){
         if (!digitalRead(BTN_PLUS)){
@@ -296,7 +292,7 @@ void speed_control(void) {
             } else {
                 last_plus = true;
             }
-        } else { 
+        } else {
             last_plus = false;
         }
         if (!digitalRead(BTN_MOINS)){
@@ -309,7 +305,7 @@ void speed_control(void) {
                 last_moins = true;
             }
 
-        } else { 
+        } else {
             last_moins = false;
         }
     }
@@ -328,12 +324,9 @@ void loop(void)
 //    Check for new received data
     Receive();
 
-
-
    if (iTimeSend > timeNow)
         return;
     iTimeSend = timeNow + TIME_SEND;
-    // Nunchuk_display();
     if (Serial) {
         if (run_mode != last_run) {
             last_run = run_mode;
@@ -371,9 +364,9 @@ void loop(void)
         speed_control();
     }
 
-LEDS.show(); // update LEDS
+    LEDS.show(); // update LEDS
+
 
-//   Nunchuk_control();
     // Blink the LED
     digitalWrite(LED_BUILTIN, (timeNow % 2000) < 1000);
 }