jerome
/
hoverboard-firmware-hack-FOC
1
0
Fork 0
Code Issues Pull Requests Releases Wiki Activity

Merge pull request #12 from Candas1/master

Browse Source 
Add FLYSKY IBUS protocol for RC remotes
pull/1/head
EmanuelFeru 6 years ago committed by GitHub
parent bdb3b00a6d 827a490f34
commit fb362f04a9
No known key found for this signature in database
GPG Key ID: 4AEE18F83AFDEB23
5 changed files with 132 additions and 51 deletions
Show Stats Download Patch File Download Diff File

28
Inc/config.h
Unescape View File

@ -10,6 +10,7 @@
//#define VARIANT_USART3 // Variant for Serial control via USART3 input
//#define VARIANT_NUNCHUCK // Variant for Nunchuck controlled vehicle build
//#define VARIANT_PPM // Variant for RC-Remote with PPM-Sum Signal
//#define VARIANT_IBUS // Variant for RC-Remotes with FLYSKY IBUS
//#define VARIANT_HOVERCAR // Variant for HOVERCAR build
//#define VARIANT_TRANSPOTTER // Variant for TRANSPOTTER build https://github.com/NiklasFauth/hoverboard-firmware-hack/wiki/Build-Instruction:-TranspOtter https://hackaday.io/project/161891-transpotter-ng
#endif
@ -61,7 +62,7 @@
* Then you can verify voltage on value 6 (to get calibrated voltage multiplied by 100).
*/
#define BAT_FILT_COEF 655 // battery voltage filter coefficient in fixed-point. coef_fixedPoint = coef_floatingPoint * 2^16. In this case 655 = 0.01 * 2^16
#define BAT_CALIB_REAL_VOLTAGE 3970 // input voltage measured by multimeter (multiplied by 100). In this case 43.00 V * 100 = 4300
#define BAT_CALIB_REAL_VOLTAGE 3970 // input voltage measured by multimeter (multiplied by 100). For example 43.00 V * 100 = 4300
#define BAT_CALIB_ADC 1492 // adc-value measured by mainboard (value nr 5 on UART debug output)
#define BAT_CELLS 10 // battery number of cells. Normal Hoverboard battery: 10s
@ -133,6 +134,21 @@
// #define DEBUG_SERIAL_USART3 // right sensor board cable, disable if I2C (nunchuck or lcd) is used!
#endif
// ###### CONTROL VIA RC REMOTE WITH FLYSKY IBUS PROTOCOL ######
/* Connected to Left sensor board cable. Channel 1: steering, Channel 2: speed. */
#ifdef VARIANT_IBUS
#define CONTROL_IBUS // use IBUS as input
#define IBUS_NUM_CHANNELS 14 // total number of IBUS channels to receive, even if they are not used.
#define IBUS_LENGTH 0x20
#define IBUS_COMMAND 0x40
#undef USART2_BAUD
#define USART2_BAUD 115200
#define CONTROL_SERIAL_USART2 // left sensor board cable, disable if ADC or PPM is used!
#define FEEDBACK_SERIAL_USART2 // left sensor board cable, disable if ADC or PPM is used!
#endif
#if defined(FEEDBACK_SERIAL_USART2) || defined(DEBUG_SERIAL_USART2)
#define UART_DMA_CHANNEL DMA1_Channel7
#endif
@ -141,11 +157,11 @@
#define UART_DMA_CHANNEL DMA1_Channel2
#endif
#ifdef VARIANT_PPM
// ###### CONTROL VIA RC REMOTE ######
// left sensor board cable. Channel 1: steering, Channel 2: speed.
#define CONTROL_PPM // use PPM-Sum as input. disable CONTROL_SERIAL_USART2!
#define PPM_NUM_CHANNELS 6 // total number of PPM channels to receive, even if they are not used.
#ifdef VARIANT_PPM
// left sensor board cable. Channel 1: steering, Channel 2: speed.
#define CONTROL_PPM // use PPM-Sum as input. disable CONTROL_SERIAL_USART2!
#define PPM_NUM_CHANNELS 6 // total number of PPM channels to receive, even if they are not used.
#endif
// ###### CONTROL VIA TWO POTENTIOMETERS ######
@ -317,7 +333,7 @@
// ############################### VALIDATE SETTINGS ###############################
#if !defined(VARIANT_ADC) && !defined(VARIANT_USART3) && !defined(VARIANT_HOVERCAR) && !defined(VARIANT_TRANSPOTTER) && !defined(VARIANT_NUNCHUCK) && !defined(VARIANT_PPM)
#if !defined(VARIANT_ADC) && !defined(VARIANT_USART3) && !defined(VARIANT_HOVERCAR) && !defined(VARIANT_TRANSPOTTER) && !defined(VARIANT_NUNCHUCK) && !defined(VARIANT_PPM)&& !defined(VARIANT_IBUS)
#error Variant not defined! Please check platformio.ini or Inc/config.h for available variants.
#endif

5
README.md
Unescape View File

@ -156,10 +156,11 @@ Most robust way for input is to use the ADC and potis. It works well even on 1m
This firmware offers currently these variants (selectable in [platformio.ini](/platformio.ini) and / or [/Inc/config.h](/Inc/config.h)):
- **VARIANT_ADC**: In this variant the motors are controlled by two potentiometers connected to the Left sensor cable (long wired)
- **VARIANT_USART3**: In this variant the motors are controlled via serial protocol on USART3 right sensor cable (short wired). The commands can be sent from an Arduino. Check out the [hoverserial.ino](/02_Arduino/hoverserial) as an example sketch.
- **VARIANT_NUNCHUCK**: Wii Nunchuck offers one hand control for throttle, braking and steering. This was one of the first input device used for electric armchairs or bottle crates.
- **VARIANT_PPM**: This is when you want to use a RC remote control with PPM Sum signal
- **VARIANT_IBUS**: This is when you want to use a RC remote control with Flysky IBUS protocol connected to the Left sensor cable.
- **VARIANT_HOVERCAR**: In this variant the motors are controlled by two pedals brake and throttle. Reverse is engaged by double tapping on the brake pedal at standstill.
- **VARIANT_TRANSPOTTER**: This build is for transpotter which is a hoverboard based transportation system. For more details on how to build it check [here](https://github.com/NiklasFauth/hoverboard-firmware-hack/wiki/Build-Instruction:-TranspOtter) and [here](https://hackaday.io/project/161891-transpotter-ng).
- **VARIANT_NUNCHUCK**: Wii Nunchuck offers one hand control for throttle, braking and steering. This was one of the first input device used for electric armchairs or bottle crates.
- **VARIANT_PPM**: This is when you want to use a RC remote control with PPM Sum singnal
Of course the firmware can be further customized for other needs or projects.

2
Src/control.c
Unescape View File

@ -112,8 +112,6 @@ void Nunchuck_Read(void) {
HAL_Delay(3);
if (HAL_I2C_Master_Receive(&hi2c2,0xA4,(uint8_t*)nunchuck_data, 6, 10) == HAL_OK) {
timeout = 0;
} else {
timeout++;
}
#ifndef TRANSPOTTER

108
Src/main.c
Unescape View File

@ -106,12 +106,25 @@ static int16_t timeoutCntADC = 0; // Timeout counter for ADC Protection
static uint8_t timeoutFlagADC = 0; // Timeout Flag for for ADC Protection: 0 = OK, 1 = Problem detected (line disconnected or wrong ADC data)
#if defined(CONTROL_SERIAL_USART2) || defined(CONTROL_SERIAL_USART3)
typedef struct{
uint16_t start;
int16_t steer;
int16_t speed;
uint16_t checksum;
} Serialcommand;
#ifdef CONTROL_IBUS
static uint16_t ibus_chksum;
static uint16_t ibus_captured_value[IBUS_NUM_CHANNELS];
typedef struct{
uint8_t start;
uint8_t type;
uint8_t channels[IBUS_NUM_CHANNELS*2];
uint8_t checksuml;
uint8_t checksumh;
} Serialcommand;
#else
typedef struct{
uint16_t start;
int16_t steer;
int16_t speed;
uint16_t checksum;
} Serialcommand;
#endif
static volatile Serialcommand command;
static int16_t timeoutCntSerial = 0; // Timeout counter for Rx Serial command
#endif
@ -132,7 +145,6 @@ typedef struct{
} SerialFeedback;
static SerialFeedback Feedback;
#endif
static uint8_t serialSendCnt; // serial send counter
#if defined(CONTROL_NUNCHUCK) || defined(SUPPORT_NUNCHUCK) || defined(CONTROL_PPM) || defined(CONTROL_ADC)
static uint8_t button1, button2;
@ -168,6 +180,7 @@ extern volatile uint32_t timeout; // global variable for timeout
extern int16_t batVoltage; // global variable for battery voltage
static uint32_t inactivity_timeout_counter;
static uint32_t main_loop_counter;
extern uint8_t nunchuck_data[6];
#ifdef CONTROL_PPM
@ -510,35 +523,65 @@ int main(void) {
#if defined CONTROL_SERIAL_USART2 || defined CONTROL_SERIAL_USART3
// Handle received data validity, timeout and fix out-of-sync if necessary
if (command.start == START_FRAME && command.checksum == (uint16_t)(command.start ^ command.steer ^ command.speed)) {
if (timeoutFlagSerial) { // Check for previous timeout flag
if (timeoutCntSerial-- <= 0) // Timeout de-qualification
timeoutFlagSerial = 0; // Timeout flag cleared
} else {
cmd1 = CLAMP((int16_t)command.steer, INPUT_MIN, INPUT_MAX);
cmd2 = CLAMP((int16_t)command.speed, INPUT_MIN, INPUT_MAX);
command.start = 0xFFFF; // Change the Start Frame for timeout detection in the next cycle
timeoutCntSerial = 0; // Reset the timeout counter
#ifdef CONTROL_IBUS
ibus_chksum = 0xFFFF - IBUS_LENGTH - IBUS_COMMAND;
for (uint8_t i = 0; i < (IBUS_NUM_CHANNELS * 2); i++) {
ibus_chksum -= command.channels[i];
}
} else {
if (timeoutCntSerial++ >= SERIAL_TIMEOUT) { // Timeout qualification
timeoutFlagSerial = 1; // Timeout detected
timeoutCntSerial = SERIAL_TIMEOUT; // Limit timout counter value
if (command.start == IBUS_LENGTH && command.type == IBUS_COMMAND && ibus_chksum == (uint16_t)((command.checksumh << 8) + command.checksuml)) {
if (timeoutFlagSerial) { // Check for previous timeout flag
if (timeoutCntSerial-- <= 0) // Timeout de-qualification
timeoutFlagSerial = 0; // Timeout flag cleared
} else {
for (uint8_t i = 0; i < (IBUS_NUM_CHANNELS * 2); i+=2) {
ibus_captured_value[(i/2)] = CLAMP(command.channels[i] + (command.channels[i+1] << 8) - 1000, 0, INPUT_MAX); // 1000-2000 -> 0-1000
}
cmd1 = CLAMP((ibus_captured_value[0] - INPUT_MID) * 2, INPUT_MIN, INPUT_MAX);
cmd2 = CLAMP((ibus_captured_value[1] - INPUT_MID) * 2, INPUT_MIN, INPUT_MAX);
command.start = 0xFF; // Change the Start Frame for timeout detection in the next cycle
timeoutCntSerial = 0; // Reset the timeout counter
}
} else {
if (timeoutCntSerial++ >= SERIAL_TIMEOUT) { // Timeout qualification
timeoutFlagSerial = 1; // Timeout detected
timeoutCntSerial = SERIAL_TIMEOUT; // Limit timout counter value
}
// Check periodically the received Start Frame. If it is NOT OK, most probably we are out-of-sync. Try to re-sync by reseting the DMA
if (main_loop_counter % 25 == 0 && command.start != IBUS_LENGTH && command.start != 0xFF) {
HAL_UART_DMAStop(&huart);
HAL_UART_Receive_DMA(&huart, (uint8_t *)&command, sizeof(command));
}
}
// Check the received Start Frame. If it is NOT OK, most probably we are out-of-sync.
// Try to re-sync by reseting the DMA
if (command.start != START_FRAME && command.start != 0xFFFF) {
HAL_UART_DMAStop(&huart);
HAL_UART_Receive_DMA(&huart, (uint8_t *)&command, sizeof(command));
#else
if (command.start == START_FRAME && command.checksum == (uint16_t)(command.start ^ command.steer ^ command.speed)) {
if (timeoutFlagSerial) { // Check for previous timeout flag
if (timeoutCntSerial-- <= 0) // Timeout de-qualification
timeoutFlagSerial = 0; // Timeout flag cleared
} else {
cmd1 = CLAMP((int16_t)command.steer, INPUT_MIN, INPUT_MAX);
cmd2 = CLAMP((int16_t)command.speed, INPUT_MIN, INPUT_MAX);
command.start = 0xFFFF; // Change the Start Frame for timeout detection in the next cycle
timeoutCntSerial = 0; // Reset the timeout counter
}
} else {
if (timeoutCntSerial++ >= SERIAL_TIMEOUT) { // Timeout qualification
timeoutFlagSerial = 1; // Timeout detected
timeoutCntSerial = SERIAL_TIMEOUT; // Limit timout counter value
}
// Check periodically the received Start Frame. If it is NOT OK, most probably we are out-of-sync. Try to re-sync by reseting the DMA
if (main_loop_counter % 25 == 0 && command.start != START_FRAME && command.start != 0xFFFF) {
HAL_UART_DMAStop(&huart);
HAL_UART_Receive_DMA(&huart, (uint8_t *)&command, sizeof(command));
}
}
}
#endif
if (timeoutFlagSerial) { // In case of timeout bring the system to a Safe State
ctrlModReq = 0; // OPEN_MODE request. This will bring the motor power to 0 in a controlled way
if (timeoutFlagSerial) { // In case of timeout bring the system to a Safe State
ctrlModReq = 0; // OPEN_MODE request. This will bring the motor power to 0 in a controlled way
cmd1 = 0;
cmd2 = 0;
} else {
ctrlModReq = ctrlModReqRaw; // Follow the Mode request
ctrlModReq = ctrlModReqRaw; // Follow the Mode request
}
timeout = 0;
@ -717,9 +760,7 @@ int main(void) {
board_temp_adcFilt = (int16_t)(board_temp_adcFixdt >> 20); // convert fixed-point to integer
board_temp_deg_c = (TEMP_CAL_HIGH_DEG_C - TEMP_CAL_LOW_DEG_C) * (board_temp_adcFilt - TEMP_CAL_LOW_ADC) / (TEMP_CAL_HIGH_ADC - TEMP_CAL_LOW_ADC) + TEMP_CAL_LOW_DEG_C;
serialSendCnt++; // Increment the counter
if (serialSendCnt > 20) { // Send data every 100 ms = 20 * 5 ms, where 5 ms is approximately the main loop duration
serialSendCnt = 0; // Reset the counter
if (main_loop_counter % 25 == 0) { // Send data periodically
// ####### DEBUG SERIAL OUT #######
#if defined(DEBUG_SERIAL_USART2) || defined(DEBUG_SERIAL_USART3)
@ -808,6 +849,9 @@ int main(void) {
if (inactivity_timeout_counter > (INACTIVITY_TIMEOUT * 60 * 1000) / (DELAY_IN_MAIN_LOOP + 1)) { // rest of main loop needs maybe 1ms
poweroff();
}
main_loop_counter++;
timeout++;
}
}

34
platformio.ini
Unescape View File

@ -13,6 +13,7 @@ src_dir = Src
;default_envs = VARIANT_USART3 ; Variant for Serial control via USART3 input
;default_envs = VARIANT_NUNCHUCK ; Variant for Nunchuck controlled vehicle build
;default_envs = VARIANT_PPM ; Variant for RC-Remotes with PPM-Sum signal
;default_envs = VARIANT_IBUS ; Variant for RC-Remotes with FLYSKY IBUS
;default_envs = VARIANT_HOVERCAR ; Variant for HOVERCAR build
;default_envs = VARIANT_TRANSPOTTER ; Variant for TRANSPOTTER build https://github.com/NiklasFauth/hoverboard-firmware-hack/wiki/Build-Instruction:-TranspOtter https://hackaday.io/project/161891-transpotter-ng
;================================================================
@ -40,7 +41,7 @@ build_flags =
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_ADC
-D PALTFORMIO
-D PLATFORMIO
;================================================================
@ -65,7 +66,7 @@ build_flags =
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_USART3
-D PALTFORMIO
-D PLATFORMIO
;================================================================
@ -86,7 +87,7 @@ build_flags =
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_NUNCHUCK
-D PALTFORMIO
-D PLATFORMIO
;================================================================
@ -107,7 +108,28 @@ build_flags =
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_PPM
-D PALTFORMIO
-D PLATFORMIO
;================================================================
[env:VARIANT_IBUS]
platform = ststm32
framework = stm32cube
board = genericSTM32F103RC
debug_tool = stlink
upload_protocol = stlink
build_flags =
-I${PROJECT_DIR}/inc/
-DUSE_HAL_DRIVER
-DSTM32F103xE
-Wl,-T./STM32F103RCTx_FLASH.ld
-Wl,-lc
-Wl,-lm
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_IBUS
-D PLATFORMIO
;================================================================
@ -132,7 +154,7 @@ build_flags =
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_HOVERCAR
-D PALTFORMIO
-D PLATFORMIO
;================================================================
@ -153,6 +175,6 @@ build_flags =
-g -ggdb ; to generate correctly the 'firmware.elf' for STM STUDIO vizualization
# -Wl,-lnosys
-D VARIANT_TRANSPOTTER
-D PALTFORMIO
-D PLATFORMIO
;================================================================
Write Preview
Loading…
Cancel
Save